10% off all orders · ends 20 November 00days 00hrs 00min 00sec Code WELCOME10

Bundle, Pen or Peptide? Sorting the Names in a STRENGTH Order

One STRENGTH order shows up under three kinds of name, bundle, pen code and peptide. A small name key stops the paperwork turning into a string of "is this the same thing?" emails.

Documentation illustration for the CLOVA guide: Bundle, Pen or Peptide? Sorting the Names in a STRENGTH Order

The STRENGTH bundle names can look like three different products once they reach your paperwork. The order says STRENGTH. The pens say KLIK500 and KLIK157. A report talks about TB-500 and BPC-157. They all point to the same thing, but only if you have mapped them, and the mapping is worth doing early.

Here is a quick way to sort the terms into a key, use it against each document you receive and avoid unnecessary confusion when someone else picks up the file.

Three layers of naming

Every term you meet belongs to one of three layers:

  • Bundle: STRENGTH is the commercial grouping on the order.
  • Pen: KLIK500 (TB-500 10mg/2mL) and KLIK157 (BPC-157 10mg/2mL) are the two separate pens you receive.
  • Peptide: TB-500 and BPC-157 are the materials named in descriptions and reports.

Put together, STRENGTH is KLIK500 plus KLIK157. The STRENGTH bundle page sets this out. You can also see each pen as its own listing, KLIK157 BPC-157 and KLIK500 TB-500, which is useful when you need a pen name matched to a peptide.

Why different documents use different layers

Documents rarely use the same layer. An order record might name the bundle, a pen label names the product code, and an analytical report names the material and a batch. Variations on spelling, such as BPC157 or TB500 without the hyphen, add another wrinkle.

None of this is a fault. It is simply what happens when documents are written for different purposes. The mistake is assuming which layer a given document uses without reading it, then treating a similar-looking term as a match.

Build a name key before you reconcile

Spend ten minutes on this when the order is placed, and you will save a lot of backtracking later:

  1. Draw a small table with the three layers as rows: bundle, each pen, each peptide.
  2. Add a column for each document you receive, such as the order confirmation, the delivery note, the pen labels and any report.
  3. In each cell, write the exact term the document uses, spelling and hyphens included.
  4. Link terms across layers only where the CLOVA listing or the label supports it.
  5. Add a batch number beside each pen. A name matches a peptide, but only a batch number ties a report to a particular pen.
  6. Mark any term that does not fit the key as unmapped, and ask about it before you rename anything.

A short worked example

A delivery note lists "KLIK500 x1, KLIK157 x1". The report you were given is headed with TB-500 and a batch number. Your key tells you KLIK500 is the TB-500 10mg/2mL pen, so the report is a candidate for that pen. The next step is to compare the batch number on the pen's label with the one on the report.

If the numbers match, record the pairing with the date. The second pen then needs its own match. A report for one pen does not cover the other, and CLOVA publishes a Certificate of Analysis only where a report is available, so do not assume one exists for each batch.

Short forms and look-alikes

Internal sheets often shorten names to "BPC" or "TB". That is fine for working notes, but put the full term from the source beside it so the shortening cannot drift into a different meaning.

Watch for look-alikes too. CLOVA's Wolverine blend (label name WOLVERINEKLIK) carries both peptides in a single pen, so it is a different product, not another name for STRENGTH. Keep the two apart in your key.

These are laboratory research materials, supplied for research use only, so the key stays a document-matching tool. It records what each paper calls each item and nothing about what the materials do.

Frequently asked questions

Is KLIK157 the same as BPC-157?

KLIK157 is the name of CLOVA's BPC-157 10mg pen, and BPC-157 is the peptide it contains. In the same way, KLIK500 is the pen name and TB-500 the peptide. Keep both terms in your key and note which one each document uses.

Does one report cover both pens?

Not automatically. Reports are tied to a batch, so check each pen's batch number against the report you hold. If a report names only one peptide, it supports only that pen.

What if a document uses a name that is not on my key?

Do not rename it to fit. Record the term exactly as written, note it as unmapped and ask the supplier to confirm what it refers to. Keep the reply with the document.

From the shop

Browse all products