10% off all orders · ends 20 November 00days 00hrs 00min 00sec Code WELCOME10

Does a GLOW Batch Report Cover All Three Peptides?

A report can name one peptide, all three or something else entirely. Here is how to read a GLOW batch report for what it actually covers and record any gaps.

Documentation illustration for the CLOVA guide: Does a GLOW Batch Report Cover All Three Peptides?

A GLOW batch report is only as broad as what it lists. Because GLOW is a blend of three peptides, a report might name all three, one or two of them, or a different product altogether, and the title at the top will not tell you which. The scope is in the detail.

CLOVA publishes Certificates of Analysis on the COAs page and on product pages where a report is available. Not every product or batch has one, so the first task is finding out whether there is a report for the pen you plan to buy. The second is reading what it covers.

Start with the sample, not the result

Before you look at any figures, read the line that says what was tested. Check three things:

  • the product name (the pen's label name is KLIKGLOW, so you may see either that or GLOW);
  • the batch number;
  • the date on the document.

The batch number is the link between paper and pen. If the one on the report matches the label on the GLOW pen you received, the report is about your stock. If it does not, the report may still be genuine, but it describes a different batch, and you should say so in your records rather than filing it as a match.

Count the peptides the report names

A GLOW pen contains BPC-157, TB-500 and GHK-Cu. Run down the report and tick off which of those names appear. A report that names only one component tells you about that one. It cannot be stretched to cover the other two, however tidy the page looks.

If the report names fewer than three, that is not a fault in itself. It is a scope fact, and the right response is a specific question to the supplier about whether further documentation exists for the remaining components.

Read each result with its units and test name

For every result, note what was measured, in what unit and under which test heading. A figure for one property should not be used to fill in a different line on your checklist. If the report states a specification or comparison value, record it with the result. If it does not, do not invent one.

Interpretation belongs with someone in your lab who can assess the analytical detail. Purchasing staff can collect and log the document, but should not make up pass marks of their own.

A scope check you can run in two minutes

  1. Does the batch number on the report match the batch number on the pen label?
  2. Is the product name consistent with the GLOW listing?
  3. Which of BPC-157, TB-500 and GHK-Cu does the report name?
  4. For each named peptide, what is reported, and in which units?
  5. Is there a date, and does it make sense against your order?
  6. What does the report not mention, and does that matter for your project?

Recording a partial match

Suppose a report carries the right batch number but names only BPC-157. The honest record might read:

Report reviewed on [date]. Batch number matches pen label. Covers BPC-157 only. Not covered by this document: TB-500, GHK-Cu. Question sent to supplier on [date].

That entry tells the next colleague exactly what is established and what is open, and it does not overstate the document. If the evidence turns out to be insufficient for your purposes, you can decide not to proceed without implying that anything went wrong.

GLOW is supplied for laboratory research use only, and a report describes a tested sample. It is not a statement about suitability for any particular project, which is a decision for your own team. What research use only means covers the wording in more detail.

Frequently asked questions

Is there a report for every GLOW batch?

Not necessarily. Reports are published on the COAs page and on product pages where one is available. If you cannot see one for the batch you want, ask the supplier and quote the batch number.

Does a report mean the pen suits my study?

No. A report describes what was tested in a sample from a given batch. Whether that fits your project is a judgement for the responsible researcher in your organisation.

What if the report matches the product name but not the batch number?

Treat it as a different batch's report. Record that the name matches and the batch does not, then ask the supplier whether a report exists for your batch.

From the shop

Browse all products